Tag Archives: water supply tubes

Overzealous kitchen faucet sprayer

SkillLevel2So I was down in the carport, which is under the house, minding my own business when I noticed water dripping on the sheets of MDF for my new workshop. I ran up stairs to the kitchen where my ever-loving wife, “Hazel” (not her real name), was cleaning up the dishes. “Something’s leaking!” I announced in my this-is-serious-but-do-not-be-excessively-alarmed voice. Hazel had been unaware of the problem because the sink and faucet looked fine but when I opened the door under the sink we were looking at the aftermath of Hurricane Katrina.

Old faucet
The old faucet doesn’t look so bad but …

After taking out the soggy contents of the sink cabinet and sopping up the water we figured out that the faucet leaked only when it was turned on and only under the sink. I pulled out the sprayer, which is on a flexible stainless steel hose, and made sure the hose was screwed on tightly to the sprayer because recently the faucet was leaking a little and that was the reason. When I turned on the faucet, it looked like the water was spraying out of the middle of the hose, which I have to admit I’ve never seen before.

I shut off the water supply, disconnected both ends of the hose, and then sawed off the connector on one end so I could pull out the rubber tubing inside.

Old leaky pullout hose with one connector cut off
Old leaky pull-out hose with one connector cut off

As you can see in the next photo, it had a good-sized hole in it. This faucet was about 9 years old and the hose saw relatively little use. (I am in no way saying Hazel doesn’t use the kitchen sink very often. She does the dishes and cleans up just as often as any other American housewife. She just doesn’t pull out the sprayer excessively when she uses the faucet. That’s my story and I’m sticking to it.)

Hole in faucet hose
Hole in faucet hose

Apparently these hoses fail pretty often because the Big Box stores carry replacement hoses that you can put in fairly easily. It wasn’t too hard to imagine some other part failing on that aging faucet in the near future so I bought a new faucet instead. Besides, I’ve never gotten in trouble for buying something new for my ever-loving wife’s kitchen.

Tools for installing a faucet. The faucet wrench is on the right with the red handle.
Tools for installing a faucet. The faucet wrench is on the right with the red handle.

Getting out the old faucet is not rocket surgery but it can be tricky because there is no room to work. To get the nut off that holds the faucet in place you really need a special faucet wrench, which is shown in the photo. You put the jaws around the nut and then twist the handle to unscrew it.

New faucet with top ring slid up over the tubes
New faucet with top ring slid up over the tubes. The plastic and metal washers and the big nut on the counter will be slid up from below after the faucet is inserted.

I gently pressed the tubes of the new faucet together so I could slide on the top ring and feed the tubes through the hole in the counter top. Then underneath the sink I slid the big washers and nut over the faucet tubes and tightened the nut to hold the faucet in place. This is where it would have been helpful to have an assistant to hold the faucet from above to keep it from turning as I tightened the big nut with the faucet wrench. Unfortunately, my ever-loving wife was unavailable at the time and I had to prairie dog it: go under the sink, tighten a little, come back out and turn the faucet straight, back down under the sink, tighten, …

Faucet connections. It's a bit crowded under there.
Faucet connections. It’s a bit crowded under there.

Hooking up the water supply tubes to the faucet tubes is not difficult–if the tubes are long enough. The tubes on the new faucet were shorter than the old faucet, which meant that the supply tubes didn’t reach. The tubes on the faucet are different lengths so that their connectors don’t hit when you feed them down the hole in the counter top. I took the longer supply tube and connected it to the longer faucet tube. Since I didn’t want to make another trip to Lowe’s right away, I “appropriated” a longer supply tube from another sink that we don’t use very often.

I have since read that it is a good idea to replace the supply tubes when you replace the faucet because they do wear out and leak. Get a handful of sizes of the braided tubes when you buy the faucet and then return the ones you don’t need. Saves trips to the store.

New faucet with soap dispenser
New faucet with soap dispenser

The old faucet used two holes in the counter top (one for the handle and one for the spout) but the new faucet uses only one. So instead of replacing the old soap dispenser with the new, I decided to install the new soap dispenser in the hole next to the faucet and leave the old one in the outside corner of the sink: one for dish soap and the other for hand soap.

Hazel is happy with the new faucet because it is stylish and easy to use. (Did I mention that she frequently washes dishes? Multiple times a week, I’d say.) I’m happy because my lumber isn’t sitting under Niagara Falls.